Submersible vs. Jet Pump: Which Is Better for Your Well?

Choosing between a submersible well pump and a jet pump can make a significant difference to your home’s water supply. The wrong pump may struggle to deliver enough water, consume more electricity than necessary, or require frequent maintenance. The right one can provide dependable water pressure while matching the depth and performance of your well.

Both pump types are used in private water systems, but they work differently. A submersible pump sits underwater inside the well and pushes water toward the house. A jet pump is installed above ground and uses suction, together with a jet mechanism in some configurations, to move water from the well.

For many drilled residential wells, a submersible pump is the natural choice, especially when the water level is deep. Jet pumps remain useful for shallow wells and certain installations where above-ground access makes maintenance easier.

The best option depends on the pumping water level, required flow rate, well construction, budget, electrical setup, and the condition of the existing system. This guide compares both types so you can make a more informed decision.

Submersible vs. Jet Pump: What Is the Difference?

The biggest difference is where the pump operates and how it moves water.

A submersible pump is lowered into the well, below the water level. Its motor drives a series of impellers and diffusers that push water upward through the discharge pipe. Because the pump is already underwater, it does not need to draw water up through a long suction line.

A jet pump stays above ground, often in a basement, utility room, well house, or other protected location. It creates a low-pressure area that helps atmospheric pressure push water into the suction pipe. A shallow-well jet pump has its jet mechanism at the surface. A deep-well jet pump places the ejector assembly down in the well and uses additional piping to operate it.

That distinction matters because a surface pump cannot lift water by suction indefinitely. In typical residential conditions, a shallow-well jet pump is generally limited to a pumping water level of about 25 feet below the pump. The practical limit can be lower depending on elevation, pipe friction, leaks, and the pump’s design.

A deep-well jet pump can serve a deeper installation, but its performance depends on the particular system and depth. Submersible pumps are commonly used in deeper drilled wells because they push water rather than relying on surface suction.

For a broader explanation of the equipment in a private water system, see our existing guide: How Does a Well Pump Work? An Illustrated Guide.

1. Submersible Well Pumps: How They Work

A submersible well pump consists of a pump assembly connected to an electric motor. The unit is installed inside the well casing, below the pumping water level, and connected to the home’s plumbing by a discharge pipe and electrical cable.

When the pump starts, rotating impellers move water through the pump stages. The water is then pushed up the pipe to the surface, where the pressure tank and pressure-control equipment help supply the house.

Submersible pumps are common in drilled private wells because they can operate at substantial depths and are available in a wide range of flow and pressure ratings. They are also generally quieter inside the home because the main pumping unit is underwater.

Advantages of submersible pumps

Suitable for deeper wells. Since the pump pushes water upward, it can serve many wells that are too deep for a shallow-well jet pump. The exact capability depends on the model, total pumping head, and required flow.

Quiet operation. The motor and pump operate inside the well, reducing the noise heard in the home compared with a surface-mounted pump.

Good performance at suitable operating conditions. A properly selected submersible pump can provide the flow and pressure required for household fixtures, irrigation, and other uses within its rated capacity.

No routine priming of a surface suction line. Because the pump is submerged, a conventional submersible installation does not rely on maintaining a primed surface suction line in the same way as a jet pump.

Less exposed pumping equipment. The pump itself is protected inside the casing from many sources of accidental damage and freezing that can affect above-ground equipment. However, the wellhead, exposed pipes, pressure tank, electrical equipment, and other components still require appropriate protection.

Disadvantages of submersible pumps

Installation and removal can be more involved. The pump must be lowered into the well and connected to the drop pipe, cable, and discharge system. Replacing a failed unit may require pulling the assembly out of the casing with suitable equipment.

Repairs may cost more in labor. Even if the failed component is relatively inexpensive, accessing a pump deep underground can increase service costs.

Sand and sediment can cause wear. Abrasive particles may damage pump components. If a well produces sand, the cause should be investigated rather than assuming a different pump alone will solve the problem.

Electrical protection is important. A submersible motor must have the correct supply, wiring, grounding, and protective devices. Electrical faults, lightning, dry running, and unsuitable operating conditions can damage the equipment.

The well must accommodate the unit. The casing diameter, available clearance, well condition, and pump dimensions must be compatible with the proposed equipment.

A submersible pump is not automatically the best choice for every property. It must still be matched to the well’s yield, water level, total head, and household demand.

2. Jet Well Pumps: How They Work

A jet pump is mounted above ground and uses a centrifugal pump combined with a nozzle-and-venturi arrangement. Water moving through the jet creates a low-pressure region that helps draw additional water into the system.

There are two main residential configurations: shallow-well jet pumps and deep-well jet pumps.

Shallow-well jet pumps

A shallow-well jet pump has its jet mechanism at the pump or near the surface. A suction pipe extends down into the water.

These systems are typically used when the pumping water level is no more than about 25 feet below the pump. That is the vertical distance to the water while the pump is operating, not necessarily the total depth of the well.

A well may be physically deeper than 25 feet while still having a shallow pumping water level, but the pump must be selected using actual operating conditions. Friction losses, altitude, and changes in water level can reduce the available suction lift.

Deep-well jet pumps

A deep-well jet pump uses an ejector installed down in the well. Water is circulated through the jet arrangement to help lift water from a greater depth than a shallow-well configuration can manage.

Many deep-well jet systems use two pipes between the surface equipment and the well’s ejector. Their practical depth and output vary by model and installation. They may be useful where a submersible pump is not suitable, but the system’s performance should be checked carefully against the manufacturer’s pump curve.

Advantages of jet pumps

Convenient above-ground access. The main pump and motor are accessible for inspection and many routine repairs without pulling equipment from the well.

Potentially lower initial cost for shallow wells. A suitable shallow-well jet pump may be a straightforward and economical solution for a property with a high water level.

Useful for certain narrow or existing well configurations. Some jet pump systems can be installed where the casing or well construction limits the available submersible options. Compatibility must be confirmed before purchase.

Easier visual inspection. Leaks, unusual vibration, corrosion, and some mechanical problems may be easier to notice because the pump is visible.

Disadvantages of jet pumps

Limited suction lift. A shallow-well jet pump cannot reliably draw water from any depth. As the pumping water level drops, the pump may deliver less water or fail to maintain prime.

Potentially noisier operation. The pump and motor operate above ground, so vibration and operating noise can be heard in the building or well house.

Priming can be an issue. Some installations require priming, and air leaks or problems with valves and suction piping can cause loss of prime.

Performance can decline with depth. Deep-well jet pumps use a different arrangement from shallow-well models, but their flow and pressure still depend on depth and operating conditions.

Two-pipe installations can be more complicated. Deep-well jet systems may require additional piping and careful adjustment compared with a single discharge pipe from a submersible pump.

Sediment can damage components. Sand and abrasive material can wear pump parts and interfere with reliable operation.

3. Submersible vs. Jet Pump: Side-by-Side Comparison

FeatureSubmersible pumpJet pump
LocationInside the wellAbove ground
Best-known applicationMany drilled and deeper wellsShallow wells and selected deep-well installations
Typical shallow-well limitNot defined by surface suction liftAbout 25 ft pumping level for shallow-well models
NoiseUsually quieter indoorsMore audible at the pump location
Access for repairsMay require pulling the pumpMain unit is easier to reach
PrimingDoes not rely on a surface suction line in a conventional installationPriming and suction-line integrity may matter
Initial installationCan involve more work inside the wellCan be simpler for suitable shallow wells
Replacement laborMay be higher because the unit must be retrievedOften easier to access
Deep-well performanceAvailable in many deep-well configurationsDepends on deep-well jet design and depth
Sediment sensitivitySand can wear pump componentsSand can wear pump and jet components
Best selection methodPump curve, pumping level, flow, total headPump curve, suction lift, jet arrangement, flow

This comparison describes general tendencies, not a guarantee that every submersible pump outperforms every jet pump. The correct model and installation matter more than the pump category alone.

4. Which Pump Is Better for Different Well Depths?

Well depth is important, but the depth of the water while pumping is often more useful for selecting a pump. The well’s total depth and the water level are not the same measurement.

Water level within about 25 feet

A shallow-well jet pump may be a practical option if the pumping water level remains within its rated suction limit and the system can deliver the required flow and pressure.

This can suit some shallow residential wells and existing installations where the pump is conveniently located above ground.

However, leave an appropriate margin for seasonal changes in water level, friction losses, and periods of high household demand. A pump that barely works under ideal conditions may become unreliable when the water level falls.

Water level deeper than about 25 feet

A standard shallow-well jet pump is generally not the right choice. Depending on the depth and system design, a deep-well jet pump or a submersible pump may be appropriate.

A deep-well jet pump can serve some intermediate-depth installations, but performance varies considerably by design. Compare its rated flow at the required head rather than relying on a single advertised maximum depth.

Deep drilled wells

A submersible pump is commonly the preferred option for many deeper drilled private wells. It pushes water upward and is available in models designed for substantial pumping depths.

The final selection still requires calculations. A pump that can lift water from a deep well may not necessarily provide the flow rate you need at your home’s required pressure.

For technical background, the U.S. Geological Survey describes jet pumps as common for shallow wells and submersible pumps as common for deeper private wells: https://www.usgs.gov/water-science-school/science/groundwater-wells

5. Flow Rate and Water Pressure: What Should You Compare?

A pump should be selected to meet the household’s water demand, not just the well depth.

Flow rate describes how much water the pump can deliver over time. It is often expressed in gallons per minute (GPM). Pressure is commonly measured in pounds per square inch (PSI). Both are important, but they are not interchangeable.

A pump may deliver a high flow at low pressure or maintain pressure while delivering less water. The required performance depends on the height the water must travel, pipe friction, pressure settings, and how many fixtures may operate at once.

When comparing pumps, review the manufacturer’s performance curve. It shows the flow a particular model can provide at different total-head conditions. The maximum flow printed on a product page may apply only under lower-head conditions and should not be treated as the expected flow in your home.

A qualified installer should account for:

  • The pumping water level while the pump is running.
  • The vertical rise from the pumping level to the point of delivery.
  • Pipe diameter, length, fittings, and friction losses.
  • The pressure required at the house.
  • Household peak demand and the well’s sustainable yield.
  • Any treatment equipment that adds resistance to flow.

Do not select a more powerful pump simply to increase pressure. An oversized or poorly matched pump can cycle too frequently, exceed the well’s sustainable output, or operate outside its efficient range.

6. Electricity Use and Operating Costs

Neither pump type is automatically cheaper to operate in every installation. Electricity use depends on the motor, pump efficiency, delivered flow, total head, run time, and system controls.

Submersible pumps can be efficient for many deep-well applications because they push water rather than relying on suction at the surface. However, efficiency varies by model and operating point. A well-matched jet pump can still be a sensible choice for a suitable shallow well.

To compare operating costs, ask for the motor’s electrical rating and estimated energy use under your actual conditions. Horsepower alone does not tell you the precise electricity cost, because a pump’s run time and efficiency also matter.

A simple way to estimate annual electricity cost is:

Annual cost = average electrical input in kW × operating hours per year × electricity price per kWh

For example, if a pump averages 0.75 kW while operating, runs for an estimated 2 hours per day, and electricity costs $0.18 per kWh:

0.75 × 2 × 365 × $0.18 = $98.55 per year.

This is an illustrative calculation, not a typical cost estimate for every home. Actual use can be substantially different depending on the pump and water demand.

The wider system also affects energy use. A correctly sized pressure tank, properly set controls, sound plumbing, and a pump operating near its intended performance range can help avoid wasteful operation.

7. Installation and Replacement Costs

The total cost of replacing a well pump depends on the pump type, well depth, electrical requirements, pipework, local labor rates, and the condition of the existing system. A submersible pump can require specialized equipment to retrieve and reinstall the unit, particularly in a deep well. A jet pump may be less complicated to access, but the surrounding piping, ejector, valves, or pressure controls may still need work.

Rather than relying on one generic price, request an itemized estimate covering:

  1. Pump and motor.
  2. Labor for removal and installation.
  3. Drop pipe, fittings, wiring, or suction piping as applicable.
  4. Pressure tank and pressure-control components, if needed.
  5. Electrical diagnosis or upgrades.
  6. Well yield or water-level testing, if a performance problem is suspected.
  7. Any work required to address sand, sediment, or other well problems.

Ask whether the quote includes testing the system after installation and whether the installer will confirm that the pump is suitable for the well’s sustainable yield.

If the existing pump has failed repeatedly, do not assume replacing it with a larger model is the solution. The underlying problem could be a low water level, a leak, an undersized pressure tank, a faulty control, or an issue with the well itself.

8. Maintenance: Which Pump Is Easier to Look After?

A jet pump is generally easier to access because its main unit is above ground. Owners and technicians can often inspect visible plumbing, connections, and signs of leakage without removing the pump from the well. However, jet pumps still need appropriate priming, leak prevention, and protection from freezing where relevant.

A submersible pump usually requires less attention to the pump itself during normal operation, but access can be more difficult if a fault occurs. The pump and motor are inside the well, so repair or replacement may require lifting the unit and its drop pipe.

Both types need the broader water system to be maintained. The pressure tank, pressure switch or controller, electrical protection, plumbing, and wellhead should be inspected as appropriate. Repeated short cycling, unusual noise, loss of pressure, or frequent breaker trips should be investigated rather than ignored.

Never open electrical equipment or pull a pump from a well unless you have the appropriate training, equipment, and safe procedures. Well systems can involve hazardous voltages, heavy suspended equipment, and confined or unstable work areas.

9. Signs That Your Existing Pump May Be the Wrong Type

A pump that frequently loses prime, struggles to deliver water, or cannot keep up with normal household use may be poorly matched to the installation. These symptoms do not prove that the pump type is wrong, but they justify checking the system.

Look into the following possibilities:

  • Declining water level: A shallow-well jet pump may no longer be able to lift water if the pumping level has fallen beyond its practical limit.
  • Insufficient flow: The pump may be undersized, worn, or operating against more head than expected.
  • Pressure fluctuations: The pressure tank, switch, control settings, or plumbing may be responsible.
  • Frequent cycling: A pressure tank problem, leak, or unsuitable pump configuration may be involved.
  • Sand or sediment: Abrasive material can damage components and may indicate a separate well problem.
  • Loss of prime: A jet pump’s suction piping, check valve, foot valve, or seals may need attention.
  • Electrical faults: A motor, cable, control box, breaker, or supply problem can mimic a pump failure.

If your home has suddenly lost water, start with the safe checks in our existing guide, No Water From Your Well? 10 Things to Check First. Avoid repeatedly running a pump that may be dry or damaged.

Frequently Asked Questions

Is a submersible pump better than a jet pump?

For many deep drilled wells, a submersible pump is the more practical choice because it pushes water upward and does not rely on surface suction. A jet pump can be a good option for a suitable shallow well and may be easier to access for service. The better choice depends on pumping water level, flow requirements, well construction, and the exact pump specifications.

Can a jet pump work on a deep well?

A deep-well jet pump can serve some deeper installations using an ejector located in the well. Its practical depth and output depend on the model, piping arrangement, and operating conditions. A standard shallow-well jet pump is generally limited to a pumping water level of about 25 feet.

Are submersible pumps quieter?

Usually, yes. Since the pump operates inside the well, much of its operating noise is isolated from the home. A jet pump’s motor and pump are above ground, where vibration and noise are easier to hear.

Which pump lasts longer?

There is no universal lifespan that applies to every installation. Quality, operating conditions, sediment, electrical protection, maintenance, and cycling all affect service life. Ask the manufacturer about its warranty and have the complete system evaluated if the pump fails repeatedly.

Can I replace a jet pump with a submersible pump?

Sometimes, but it is not always a direct swap. The well casing must accommodate the pump, and the installation may require a different drop pipe, electrical cable, discharge connection, and wellhead fitting. The pump must also be sized for the well and home’s demand. Have a qualified well contractor assess the conversion before buying equipment.

Does a submersible pump need a pressure tank?

Most conventional residential systems use a pressure tank and pressure controls to supply water between pump cycles and help prevent rapid cycling. Some variable-speed systems use different control arrangements and may require a smaller tank, but the manufacturer’s design requirements must be followed.

Should I choose a more powerful pump for better pressure?

Not automatically. Pressure depends on the pump’s performance at the system’s total head, the pressure controls, pipework, and the household’s demand. A pump that is too large can cause excessive cycling or exceed the well’s sustainable yield. Select the pump based on a proper flow and head calculation.

Final Recommendation

For many deeper drilled private wells, a properly sized submersible pump is the strongest starting point because it pushes water from inside the well and can serve a wide range of depths and flow requirements. For shallow wells, a jet pump may offer a simpler and more accessible installation when the pumping water level stays within the model’s rated limits.

Before buying either type, confirm the pumping water level, the well’s sustainable yield, required flow and pressure, casing dimensions, electrical supply, and the pump’s performance curve. Compare the complete installation and maintenance costs rather than the purchase price alone.

A well-matched pump should supply the home’s water needs without being forced to operate outside its intended range. If you are replacing an existing unit, investigate why the old system failed before choosing the replacement. That is often the most effective way to avoid repeating the same problem.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top