An annual well maintenance checklist helps you catch changes in water quality, pressure, and the condition of the wellhead. Start with a visual check and a review of your records. Then schedule water tests with a certified lab and arrange any checks that require a contractor. Write down what you find so you can compare it with next year’s readings.
Table of contents
- Start your annual well maintenance checklist with the records
- Look at the cap, casing, and ground around the well
- Check changes in land use and drainage
- Schedule the right water tests
- Record a pressure and flow baseline
- Look after the pressure tank, controls, and service area
- Review each part of the treatment system
- Get a written professional inspection report
- Set a schedule for storms, repairs, and seasonal use
- A checklist you can copy into your well log
- What a useful maintenance log looks like
- Frequently asked questions
Start your annual well maintenance checklist with the records
Find the well construction record and the first available test results. The record may show depth, casing, drilling date, and the yield measured when the well was put in. Keep pump and tank model numbers, treatment instructions, and service invoices with it. For example, an invoice for a past pump replacement may tell a technician the depth of the pump, even when the original construction record does not. If you recently bought the property, ask the previous owner or the local well records office what documents are available.
Then sketch the route from the well to the pressure tank, treatment equipment, water heater, and main outlets. Mark any sample taps before and after treatment. If you share a well, include who approves repairs and which home gets its water from each line. A sketch does not need to be to scale. Its main value is that it helps a tester sample the right water and gives a technician a starting point when you describe a problem.
Choose a place for the log that anyone in the house can reach. Put the contractor, local health department, lab, and emergency water contacts on the first page. Add a record for the current year and a reminder for the next visit.
Look at the cap, casing, and ground around the well
Walk around the well from ground level. Check whether the cap appears seated and the exposed casing and conduit look intact. Look for new cracks, dents, loose parts, or damage left by mowing or vehicle traffic. Then take a photo from the same angle as last year if you have one. A comparison can make a small change easier to see. Leave the cap in place and keep clear of damaged wires, flooded equipment, and any well pit or vault.
Look at the ground around the casing. Water that collects near the well after a storm gives you something concrete to discuss with a contractor. Also check whether landscaping or recent construction changed the slope or buried part of the casing. Mark the location before scheduling any work nearby. Ask your local well program or contractor which clearance and location rules apply to your property. A setback you read about for another state may not apply to your well.
Finally, check that the well is easy to reach for service. Move ordinary items that block the approach if you can do so safely. A contractor needs room to work and to inspect the cap, conduit, and surrounding ground. The Wellowner.org annual inspection guide explains which parts belong in a professional checkup.
Check changes in land use and drainage
List the changes that happened since your last inspection. For instance, a new driveway can redirect runoff. A septic repair may have changed where equipment crossed the property. A new animal enclosure, chemical storage area, or fuel tank may prompt a question for the local health department. The goal is to describe what changed and where it happened. The distance and direction to the well, the water level, and the type of ground can all matter.
Ask your septic service company for the last maintenance date and the location of the system. Keep their record separate from the drinking water lab report. If there is an old well on the property, ask the local well program how to check whether it was properly sealed. Do not enter or open an old well to investigate it. An old photo or property plan may be enough for the first conversation with a licensed contractor.
After a major storm, look for water marks, standing water, or erosion around the well from a safe place. If floodwater covered the well, or if you suspect sewage or chemicals, use a known safe water supply and follow local health guidance. For clues after a storm, see our guide to brown well water after heavy rain.
Schedule the right water tests
The CDC recommends testing a private well at least annually for total coliform bacteria, nitrate, total dissolved solids, and pH. Ask your local health department which additional tests fit the area, the well construction, and the people using the water. For example, local geology or nearby land use may guide extra testing. See the CDC’s guidance on testing private well water for when to test and how to find a state-certified lab.
Call the lab before collecting water. Ask for bottles, handling instructions, and the deadline for delivery. Choose the tap that answers the question. A sample before treatment can show what enters the house. A treated drinking tap can show what the household uses and whether a treatment step is performing as expected. Ask the lab whether you should collect both. Follow its sampling directions, which may differ by contaminant and by purpose.
Then date and label the sample point. Keep the whole lab report, including units and reporting limits, so you can compare results later. Our guide to well water testing frequency explains common reasons for arranging a test between annual visits.
Record a pressure and flow baseline
Choose one ordinary cold tap and note the pressure at a gauge near the tank if it is easy to read. Record the reading with taps closed and the behavior during a steady draw. Then note when the pump starts and stops if you can tell without opening an enclosure. These observations help a contractor spot a change in operation. A gauge at the tank only shows pressure at that point. A restriction farther along the line may reduce the flow at taps without an obvious change beforehand.
Note any air from faucets, new sounds, or repeated starts. For example, a pump that restarts when no one is using water may warrant a leak check. A short burst of low flow at one faucet can have a different cause. Tell the contractor which fixtures behave differently. For a refresher on the main components, see our guide to how a well pump works.
Keep the conditions with the readings. Write down which tap was open, whether other fixtures were running, and whether there had been heavy use before the check. Next year, use the same fixture and similar conditions if possible. The comparison is more useful than a bare number without context.
Look after the pressure tank, controls, and service area
Keep the area around the pressure tank dry and accessible. Check for visible drips, corrosion, or a gauge that no longer moves as expected. Photograph the equipment label if it is readable. Then check your notes for a change in starting and stopping behavior. If the system uses a variable-speed drive, record the model and alarms. The expected operation can differ from a setup with a conventional switch.
A well professional can compare the tank, controls, and pump with the manufacturer’s instructions. Ask which measurements they took and what result they expect. For example, if they report low tank drawdown, ask how they measured the usable water between pump starts. If they suggest replacing a pressure switch, ask whether they checked the gauge and its sensing connection. Keep covers on electrical parts and leave work on live or pressurized equipment to the technician.
If the service area floods or the controls smell burned, step away from the equipment and request service. A new alarm or recurring trip also deserves investigation. Have the contractor tell you what the code means for your model so you know what to mention if it returns.
Review each part of the treatment system
Make a short list of the jobs your equipment performs. One device might trap sediment, another might reduce hardness, and another might target a particular test result. The schedule depends on the model and on what enters the house. Check the last service date, alarm status, and any pressure readings on both sides of a filter. For example, a pressure drop under ordinary demand can be a better clue about a loaded cartridge than its color alone.
Ask your installer when to sample water after replacing media or changing the system. If the equipment is there for a health-related contaminant, ask how a lab will verify the result at the tap the household drinks from. Also confirm what the household should do while a treatment unit is out of service. Our whole-house well water filter comparison explains how different devices fit together.
Then add service dates to the household calendar. Note the exact part numbers for filters, lamps, or other parts you may need. If a service company stocks the parts, check its contact details. Clear records help when a family member or future homeowner has to arrange the work.
Get a written professional inspection report
Ask what the visit includes before the contractor arrives. Start with the wellhead, flow and pressure, visible plumbing, controls, and pressure tank. Discuss whether the inspection includes a water sample, a lab fee, or checks inside a treatment unit. The services vary. One visit might cover a visual inspection and a brief flow check. Another might include a longer test or a closer review of equipment issues. Have both companies quote the same scope if you want to compare prices.
Walk through the findings when the work ends. For example, ask whether the technician saw a condition that needs immediate attention or a change that can be reviewed next year. Ask for model numbers, readings, and the conditions under which those readings were taken. If the well has a history of low supply, ask whether the test answers a question about capacity or only about flow at a fixture. A written explanation can help you plan the next decision.
Finally, record the next service date. Save any lab results once they arrive and follow up on items left open. A report is more useful if you can tell from the record which repairs were done and what changed afterward.
Set a schedule for storms, repairs, and seasonal use
An annual inspection gives you a baseline. Certain events can call for action before the next visit. If water changes color, taste, or smell, or if the well floods or gets repaired, ask your health department about testing. Tell the lab whether the well has just been disinfected or worked on. The timing and sample point matter when you use results to decide when the well is ready for regular use.
For a seasonal home, ask a local well professional how to bring the system back after a long shutdown. Pay attention to equipment that could have frozen or pipes that may have drained. Also ask what maintenance is due on any treatment stage. A visible check and a call to the right people are useful before guests arrive and put new demand on the system.
Keep a list of the planned checks for the year. For example, mark when to inspect after heavy rain, when the lab accepts samples, and when your filters or service contract come due. Then add the company you will call if the pump stops. If a major repair prompts a comparison with a new well, see our well drilling cost guide for what to include in the estimate.
A checklist you can copy into your well log
Records. Save the construction report, pump and tank labels, invoices, sample locations, and emergency contacts. Update any changes to the piping or shared well agreement. Wellhead. Take a dated photo and note the condition of the cap and visible casing. Check for ponding, erosion, and changes in access. Water quality. Book certified testing and save the complete lab report with tap names and results.
Pressure and treatment. Record a normal gauge reading under a known draw, unusual pump behavior, and the last service date for equipment. Confirm where treated drinking water comes from. Professional visit. Ask for the scope and the measurements in writing. Then record the work done, follow-up tests, and which items need another visit. Emergency plan. Keep current phone numbers and a known safe backup water source on the same page.
Put a date beside each item as you finish it. If you share the well or buy the house with someone else, agree who will review results and request service. Mark items that remain open. Start next year with that list so unresolved issues do not disappear when the calendar turns.
What a useful maintenance log looks like
Consider a household that changes its filter every time a shower feels weak. The next year, it keeps a short log instead. Each month the family notes the pressure at the tank and the flow at the same cold tap. They write down when a filter was changed and how the flow responded. One morning, the gauge at the tank shows its usual reading, but flow falls at several fixtures. The old notes help the contractor decide which parts to test first.
The same log also helps with water quality. A test from the untreated port and another from the kitchen filter tell different stories. Write down which one the lab received. Then note the date of any treatment service. When the next report arrives, compare results collected at the same location and in the same units. If a result changes, ask whether it reflects source water, service to a treatment unit, or a difference in sampling. Even a plain notebook works if the dates and locations are clear.
Frequently asked questions
Can I do the entire annual well inspection myself? You can keep records, observe visible conditions, and arrange water tests. A qualified contractor should handle work inside the well, on electrical controls, or on pressurized equipment.
Is clear water a reason to skip testing? Water can look clear even when a lab finds contaminants. Use the recommended schedule and ask about extra tests for your area and circumstances.
Where should I keep the last test report? Store it with the well records and retain the original sample date, location, units, and any notes. A photo of just one number is hard to interpret later.
Should I test again after a repair? Ask your local health department which sample is appropriate and when to collect it. Tell them what parts of the system were opened or changed.
Related guides
When to test private well water · How the pump and tank work together · How to evaluate a well drilling estimate