If a lab finds coliform bacteria in well water, use bottled water or another known safe supply and call your local health department. Then check whether the report also lists E. coli. A positive E. coli result points to likely fecal contamination and calls for prompt action. A positive total coliform result also deserves attention. After the repair or disinfection, have a certified lab test the water again. Ask the health department when you can use the well for drinking and cooking.
Table of contents
- What coliform bacteria in well water mean
- What to do about coliform bacteria in well water
- How bacteria enter a private well
- How to test for coliform bacteria in well water
- Repair the well and retest after disinfection
- What to do when coliform bacteria return
- How to keep track of your well water tests
- Frequently asked questions
What coliform bacteria in well water mean
Coliforms are a large group of bacteria that occur in soil, on plants, in surface water, and in the digestive tracts of people and animals. A drinking water lab uses total coliforms as an indicator. Their presence suggests that something may have entered a part of the well or plumbing system that should have been protected.
The bacteria detected may come from an environmental source, or the finding may accompany germs that cause illness. On its own, the result cannot show how the organisms entered the system. The lab report and a site inspection answer different parts of the question.
Check the E. coli line separately
E. coli is a member of the coliform group. A positive E. coli indicator test suggests contamination with fecal material from people or animals. Treat it as urgent even if the water smells and looks normal. This standard indicator test does not identify whether a particular disease-causing strain is present.
Its value here is that it flags a route by which other harmful organisms can enter the supply. A report that detects total coliform but does not detect E. coli is a different finding. It still warrants using safe alternative drinking water and following your local health department’s instructions. See the CDC guide to well water test results.
First, look for the sample location, date, and method on the report. For example, some reports say present or absent, while others provide an estimate of the number of organisms in a stated volume. Also look for notes such as sample too old, invalid, or results affected by background growth.
In turn, those notes can change what the lab can conclude. If your report lists total coliform but has no E. coli line, call the lab to find out whether it tested for E. coli and whether an additional sample is needed. A blank field may mean the test was never ordered.
What to do about coliform bacteria in well water
Give everyone who uses the well the same instructions. Use commercially bottled drinking water or another supply confirmed safe for drinking and preparing food. Also, think beyond the glass at the kitchen sink. For example, ice, cold drinks, infant formula, and brushing teeth can all involve swallowing water.
Shut off the refrigerator ice maker if it draws from the affected supply and discard ice made with that water. A coffee machine or an ordinary refrigerator filter should not be your substitute for a safe water source. If the property has a guest house, rental unit, or shared supply, ask the local health department what to tell the other users and do so promptly.
Ask before boiling well water
For some microbial contamination events, health officials may advise boiling water if a safe alternative is unavailable. Ask for specific instructions for your location and situation. Boiling cannot address chemical contamination and can concentrate some dissolved contaminants. In particular, this distinction matters after flooding or when the same lab report flags nitrate or another chemical.
Ask the health department about bathing, washing dishes, doing laundry, and water for pets. Advice can depend on the contaminant, evidence of sewage or chemicals, and who lives in the home. To help them, give the actual lab report to the official advising you so you do not have to interpret the combined risks yourself.
Contact a healthcare professional if someone becomes ill after drinking from the well, and tell them about the water result and the dates of possible exposure. Keep the water response separate from any medical evaluation. Do not wait for symptoms to put a safe drinking water plan into effect.
Get in the habit of checking where visitors typically fill a glass or bottle. A sign on the main tap and safe water placed where people prepare food can reduce the chance of someone inadvertently using untreated water. Review any special feeding needs with the child’s healthcare provider.
How bacteria enter a private well
A positive result can originate in the well, the connecting plumbing, the sampled tap, or the sampling process itself. For example, issues to investigate include a damaged or loose cap, deteriorated casing or seals, ponding around the wellhead, or a recent service visit that opened part of the system. Backflow through an improperly protected hose connection is another route a contractor may consider. After a storm, a shallow well or one subject to surface water intrusion can behave differently after storms from a well with an intact casing and seal. If the result follows heavy rain or a change in color, compare the timeline with our guide to brown well water after heavy rain.
Look for damage around the well cap
From outside, look for visible signs a contractor will want to know about. Note whether the cap looks loose, a conduit entering it appears damaged, or water drains toward the casing. Then photograph visible conditions without removing the cap. Record recent trenching, pressure loss, pump work, flooding, or septic problems.
If possible, include the dates if you have them. A contractor can then decide whether to investigate a surface entry path, system plumbing, nearby sources, or several possibilities at once. Avoid handling electrical components or entering pits and vaults.
The timing matters, but it cannot establish the source on its own. A positive result after a pump replacement could reflect material introduced during work, a damaged component discovered after the work, or something unrelated that would have been present anyway. A positive sample from one bathroom tap with a negative result elsewhere may point toward local plumbing or the faucet, but the lab and contractor will decide what pattern of samples can verify that. However, collecting a second sample is useful only when the site and method fit the question. Use safe water while troubleshooting, even if you suspect the sample location rather than the well.
How to test for coliform bacteria in well water
Call a state-certified drinking water lab before attempting to collect another sample. Ask how to select and prepare the tap, whether to remove the aerator, how long to flush, and which container to use. Follow its protocol, which may differ depending on whether you want to assess the water entering the house or the water at a specific fixture. Next, use the bottle the lab provides and leave any preservative in it.
Avoid contacting the inside of the cap or bottle. Finally, keep the sample in the conditions specified by the lab and deliver it within its holding time. A swab or strip bought for general home use does not answer the same question as a certified drinking water test. See our step-by-step guide for collecting well water samples.
Label each sample by tap
Label each sample with the exact tap, treatment status, date, and time. If treatment is installed, note whether water went through it. Where the lab recommends comparing the raw supply with a treated faucet, collect separate bottles for each. Taking two bottles from one tap is useful only when someone is trying to confirm that tap’s result.
However, it will not show whether bacteria entered before or after a treatment unit. A house with multiple branches, a storage tank, and a guest building may need more than one point sampled. Have the contractor draw the system so its sample locations can be matched to the report later.
Ask what will happen if a sample misses the holding time, reaches the lab warm, or has a compromised bottle. A lab may mark the outcome as invalid or add a qualification. Follow its instructions for repeating the collection.
If the first test was a screening kit, tell the lab what it measured, whether the sample was pre- or post-treatment, and how it was handled. Our guide to lab and DIY water test kits explains what to check when shopping for a test. When a result will decide when your household can resume using the water, use a certified lab and local health guidance.
Repair the well and retest after disinfection
Bring your report and any well record to a licensed or otherwise qualified well contractor in your area. Ask for an inspection of the cap, casing, seal, and likely pathways for surface water, along with a look at the parts of the system that were repaired or opened recently. If the lab samples point farther downstream, get appropriate help for the affected plumbing or equipment. Discuss how the repair and disinfection will be sequenced. Where there is a physical defect, treat the proposed repair as part of your plan, because a one-time disinfection does not prevent water from entering through the same defect the next time it rains.
Ask how the contractor will disinfect the well
Professional well disinfection can be appropriate after a positive test, depending on local guidance and the cause. The approach depends on construction, water volume, components, and local instructions. Ask the contractor which parts of the well and plumbing will be treated, how equipment that could be affected will be handled, and when you can sample afterward. Regional advice may also cover disposal of disinfectant-containing water.
Keep using your interim drinking water supply. Even so, the smell of chlorine shows the presence of disinfectant but cannot confirm that the underlying contamination problem has been resolved. The Minnesota Department of Health guidance on bacterial safety describes this sequence of safe water, disinfection, and testing.
Arrange follow-up testing through the certified lab with timing recommended by the health department and contractor. Make sure the lab knows disinfection was performed and ask whether it needs evidence that residual disinfectant has cleared. Follow the local instructions about how many tests are needed and whether they should be spaced apart.
For example, a sample collected before a repair, immediately after disinfecting, or from the wrong location does not answer the same question as a properly timed sample from the tap you intend to use. Keep each result next to the date and record of the work. Ask the health department to confirm when you can resume use, particularly if E. coli, flooding, or several simultaneous contaminants were involved.
What to do when coliform bacteria return
Repeated positives warrant investigation of the recurring source. Compare which sample points were positive, which were clear, and how results relate to rain, service work, and periods the home sat empty. Look for differences in how samples were taken and what treatment or plumbing configuration was in place.
Share this timeline with the health department and contractor. A system with a clean raw-water sample but positive downstream sample calls for different investigation than a system with bacteria repeatedly present before treatment. Ask whether the well construction is appropriate for the site and whether additional sampling could clarify the pathway.
Check whether you need a lasting fix
There are several possible outcomes. A repairable wellhead defect might call for replacing a damaged cap and addressing drainage. Problems with the groundwater or the well structure could require more extensive evaluation, rehabilitation, or another water source. A household disinfection system may be part of an engineered solution if the source can be safely managed under local guidance.
If ultraviolet equipment is proposed, ask about its validated capacity, the water quality it needs, any pretreatment, alarms, lamp and sleeve service, and a method to confirm performance. These systems depend on the water actually passing through the treatment unit at conditions for which it was designed. Do not treat an equipment purchase or an alarm reset as proof of safe water. Use new samples and health department guidance to make that decision.
An ordinary whole-house sediment or carbon cartridge has a different job. If the home needs multiple treatment steps, have a specialist specify what each does and how each one will be verified. The Well Owner Hub whole-house filter guide explains how to compare system types. get a written record of the work and operating instructions for the configuration you choose. Ask who should be called when an alarm sounds and what water the household can use while equipment is out of service.
How to keep track of your well water tests
Add the lab and contractor to your home maintenance contacts. Keep the well construction record, sampling instructions, and service history together. A spreadsheet or simple binder works as long as you can tell where each sample came from and what work preceded it. Make a note of the next date the health department recommends.
CDC’s annual testing guidance includes total coliform bacteria, nitrate, total dissolved solids, and pH. A history of positive results can warrant extra tests around times when the well has been vulnerable, such as after heavy storms or work on the system. Our well water testing frequency guide describes common triggers for a new sample.
Watch for changes after storms and repairs
Walk around the wellhead from time to time and after major changes to the site. Look for new pooling, disturbance from vehicles or equipment, damage to exposed components, or anything that makes the well harder to reach for service. An accessible wellhead makes regular checks easier and helps a contractor see what might have changed between two visits.
If you start using a property that has been vacant or get control of a shared well, establish your own baseline with help from the local health department. Notes from a prior owner are a place to start. Ask for the dated lab report and the sample location before relying on past testing.
Prepare for the next incident while the water is usable. Identify where you can get safe drinking water, how you’ll reach people who share the well, and which taps use raw or treated water. Learn whom to call outside normal work hours. Include the number and website for your local health department, along with instructions about how to access the certified lab on weekends. A plan written down next to the last test report is more useful during a real problem than a list of equipment model numbers alone.
Frequently asked questions
Is a positive total coliform result the same as a positive E. coli result? No. Total coliform is a broad indicator, while E. coli indicates likely fecal contamination. Use safe alternative drinking water and ask the health department how to respond to the precise lab result.
How could water test positive if it tastes fine? Indicator bacteria can be present without a noticeable change in taste, appearance, or odor. A laboratory test measures what the senses cannot establish.
Can a bad sample produce a positive result? Problems during sample collection can introduce bacteria. Ask the lab to review the procedure and tell you how to repeat the test. Continue using safe water while you and your health department resolve the result.
Will a single negative follow-up result end the precautions? Follow your health department’s instructions about sampling dates and how many results are needed. In particular, the answer can depend on whether the well flooded, the type of contamination, and what was repaired.
Should I test neighbors’ wells? Share the concern with the health department. They can advise whether other households may be affected and how neighbors can arrange tests for their own wells.
Related guides
How to collect a well water sample · When to schedule well water testing · How to compare whole-house well filters